Aim of the work Creating a solution from solid compounds, separating compounds from mixtures using their differences in solubility, determining the percentage of table salt in a sand-salt mixture. Used compounds Solid sodium chloride in a mixture with sand, dried to a constant weight at 105ºC. Equipment Beaker, glass rod, funnel, conical flask, measuring cylinder (250 cm 3), hydrometer, filter paper. 1) In a conical flask, dissolve the NaCl from a previously weighed sand-salt mixture. To do that, add about 50 cm3 of distilled water to the mixture. Stir the solution with a glass rod and then filter it. For filtration, fold the filter paper in half twice. Cut one corner for the filter paper to distribute evenly to the wall of the funnel (see
Surface TextureContour Measuring Instruments Explanation of Surface CharacteristicsStandards Definition of Surface texture and Stylus instrument Profile by Stylus and phase correct filter ISO4287: '97 and ISO3274: '96
Laura Lüll KRG11/21 Total station: Problems 1. Distinguish between transits and theodolites. - Transits and theodolites are instruments for measuring horizontal and vertical angles. The distinction between these instruments is not very clear. At first, both of instruments were called theodolites. The instruments that were manufactured with long telescopes and could not be inverted end for end were called theodolites. As technology developed, people started making instruments with shorter telescopes that could be inverted or transited – these machines were called transits. Time
Equipment Conical flasks (250 cm3), 2 burettes (25 cm3), pipette (10 cm3). Procedure A. Determining the concentration of a hydrochloric acid solution through titration 1. To determine the concentration of the acid solution take the NaOH solution with a known concentration (the standard solution) and pour it into the burette (α in figure 2.2). See that there are no air bubbles near the tip. Fill the burette until the 0-point of the scale. When measuring the level of the solution keep your eyes at the same level with the liquid level. The lower edge of the liquid level has to be at the 0 calibration mark (see figure 2.1). Work solutions are the solutions which are going to be used for pipetting or Figure 2.1 added from the burette. This step is necessary to ensure that the measuring of concentration is not changed by water or solvent of another
kus nad said teada X firma toodete kohta. Küsitluses osalevad X firma kliendibaasi kliendid, esialgu on küsitluse valimiks 25 püsiklienti. Kirjandus 1. http://en.wikipedia.org/wiki/Customer_satisfaction 2. http://en.wikipedia.org/wiki/Customer_service 3. http://sbinfocanada.about.com/od/customerservice/a/custservrules.htm 4. Gerson, R. F. (1996). Great Customer Service For Your Small Business. Menlo Park (Calif): Crisp Publications 5. Gerson, R. F. 2000. Measuring Customer satisfaction. Menlo Park (Calif): Crisp Publications 6. Godin, S. 2000. Promission marketing. Fontes 7. Hayes, B.E. 1997. Measuring customer satisfaction.AQS 8. Hill,N. Allen, R. 2007. Customer Satisfaction: The Customer Experience Through the Customer's Eyes. Cogent Publishing 9. Karjaste, M. 1998. Miks klient rahul ei ole? Kuidas meeldida Eesti kliendile. Tallinn: Kirjastus Ilo 10. Mauring, T. 2001. Rahulolematu kliendi hind
Aim Determining the identity of an unknown metal. Measurement of gas volume, calculations with gases based on reaction equations. Substances 10% solution of hydrochloric acid, 5,0...10,0 mg piece of a metal. Equipment Apparatus for measuring the volume of gas, measuring cylinder (25 cm 3), funnel, filter paper, thermometer, barometer and hygrometer. Experimental procedure 1. The experimental apparatus (Figure 1) consists of two burettes connected with a rubber hose (a), which is filled with water. One burette is connected to a test tube (b), in which the metal reacts with the acid. 2. Preparation for the experiment. Remove the test tube and wash it carefully with distilled water. Firmly attach the test tube
Elektrienergi arvestamine - Kasulikku tööd teeb ainult aktiivtakistus. Reaktiivtakistus nihutab voolu ja pinget, kuid koormab ülekandeliine. Elektrienergiaarvestid mõõdavad aktiivkomponenti või reaktiivkomponenti. Aktiivenergiarvesti suudab mõõta lubatud hälbe piirides ainult aktiivenergiat E= UIt, kus t on aeg voolu ja pinge faasi nihkega kuni cos = -0,5 (induktiivsus) või või cos =0,8 (mahtuvus). 28. MÕÕTEVAHENDITE OMADUSED Mõõtesüsteemi tundlikkus, sensitivity of a measuring system - Mõõtesüsteemi näidu muutuse ja selle tekitanud mõõtesuuruse väärtuse muutuse suhe. Mõõtesüsteemi tundlikkus võib sõltuda mõõtesuuruse väärtusest. Mõõtesüsteemi selektiivsus, selectivity of a measuring system - Mõõtesüsteemi omadus, kui mõõtesüsteemi kasutada vastavuses kindla mõõteprotseduuriga, mille juures mõõtesüsteem annab ühe või mitme mõõtesuuruse
Aim Determination of total and carbonate hardness of tap water using titration technique. Eliminating total hardness with a Na+ ion-exchange softener. Reagents 0.1 M hydrochloric acid, 0,025 M and 0,005M trilon-B solution, buffer solution (NH4Cl + NH3∙H2O), indicators methyl red (mr) or methyl orange (mo) and chromogen black ET-00. Apparatus Conical flasks (250 ml, 500 ml), measuring cylinder (25 cm 3), burette (25 cm3), pipettes (100 cm3). Experimental Procedure A Determination of carbonate hardness 1. Rinse the 100 cm3 pipette 2...3 times with a small amount of the test water. Wash the conical flask with distilled water. Pipette 100 cm 3 of the test water and transfer it into the conical flask, add 3...4 drops of indicator mo or mr. 2. Prepare the burette – remove any air bubbles from the nozzle and fill with 0.1
The aim of the experiment To determine the molar mass of carbon dioxide in three different ways; 1) using the Ideal Gas Law equation, 2) using the molar volume of a gas at NTP, 3) using the relative density to air Equipment CO2 tank, a flask with a rubber stopper (300 cm 3), technical balance, measuring cylinder (250 cm3), thermometer, barometer. Method 1. Determine the mass (m1= mflask+stopper+air) of the dry flask with a rubber stopper by weighing on a technical balance. Draw a line on the flask at the bottom edge of the stopper in order to measure the volume of the flask in step 5. 2. Fill the flask with carbon dioxide gas. Direct the gas from the CO 2 tank into the flask for about 7-8 minutes. The tip of the hose has to be in the bottom but not very closely
201 Hit 202 Blocking stick 203 Lifting stick 204 Incorrect kick 205 High kick 206 High stick 207 Incorrect push 208 Tackle/Trip 209 Holding 210 Obstruction 211 Incorrect distance 212 Lying play 213 Hands 214 Header 215 Incorrect substitution 216 Too many players on the field 217 Repeated offences 218 Delaying the game 219 Protesting 220 Inc.entering the rink 221 Inc.equipment 222 Measuring stick 223 Inc.numbering 224 Play without stick 225 Non-removal of broken stick 226 Penalty at penalty shot 501 Violent Hit 502 Dangerous play 503 Hooking 504 Roughing 505 Repeated offences 101 Unsports.behaviour 301 M1, 302 M2, 303 M3, 401 Time Out, 402 Penalty shot. PP Power play, SH Short handed, ESH Equally short handed, DP Delayed penalty, PS Penalty shot, MPS Missed penalty shot, WG Without goalkeeper, EN Empty net, OG Own goal, ET Extra time
Transport of impurities such as dust, rust, water, combustion products etc, away from the engine to filters and separators. The lubricating oil system for a diesel engine is shown schematically in the figure. Used oil drains to the bottom of the crankcase and passes through strainers by gravity to the drain tank. A pump (5) sucks oil from a lubricating oil drain tank (3), which in large engines is most often a bottom tank below the main engine. It is fitted with an air vent, level measuring gauge and sounding pipe. To reduce the possibility of contamination of the lubricating oil in the bottom tank as a result of leaks, all the remaining bottom tanks containing, for example, fresh water, seawater or fuel oil, can be separated from the lubricating oil bottom tank by coffer-dams (2). To safeguard the pump, a course filter (4) is inserted between the pump and the bottom tank. The pump forces the oil a through lubricating oil cooler
World's Fair, it was initially criticized by some of France's leading artists and intellectuals for its design, but it has become a global cultural icon of France and one of the most recognisable structures in the world. · The Eiffel Tower is the most-visited paid monument in the world. Introduction · It's 324 metres tall, what maks it the tallest building in Paris(It's about as tall as a 80-storey building!). · Its base is square, measuring 125 metres on each side. · During its building, the Eiffel Tower surpassed the Washington Monument to become the tallest man-made structure in the world, a title it held for 41 years until the Chrysler Building in New York City was finished in 1930. Due to the addition of a broadcasting aerial at the top of the tower in 1957, it is now taller than the Chrysler Building by 5.2 metres. Introduction · The top level's upper platform is 276 m above the ground,
ning taasehitada looduslikku maastikku tulevikus. IDII ja IDIII fragmendid aladel Br1 ja Br2 asuvad majandusliku arengu piirkonnas piki Jangtse kallast, Yao järve ja Ge järve ning linnade lõunapoolsel kaldal. Valglinnastumine areneb ökoloogilisel alal. Linna piirkond arenes suuresti väljaspool puhvrivööd ning linna areng hõlmas vaid mõne loodusliku ala ning liikus ümber objekti fragmentide ja isolatsiooni efekt mõjutas loodusmaastiku killustatust. Kasutatud kirjandus Su W. Measuring the Impact of Urban Sprawl on Natural Landscape Pattern of the Western Taihu Lake, China http://www.sciencedirect.com/science/article/pii/S0169204609002382
-worn by the thrower during -worn by the thrower delivery from the hack and by -normal athletic sole sweepers - teflon sole Curling shoes, showing a slider sole Other equipment Curling pants, made to be stretchy to accommodate the curling delivery A stopwatch to time the stones while sweeping Curling gloves and mittens, to keep the hands warm and improve grip on the broom Measuring which stones is closest to the centre of the house Scoring the winner is the team having the highest number of accumulated points Points are scored at the conclusion of each of these ends -when each team has thrown its eight stones the team with the stone closest to the button wins that end A typical curling scoreboard used at clubs
Ekspluatatsioonikulud 34. Malm 34. Mergel 35. Management 35. Juhtimine, korraldamine 36. Mapping 36. Kaardistamine 37. Margin 37. Äär 38. Marshy ground 38. Soopinnas 39. Masout 39. Masuut 40. Mat foundation 40. Alusplaat 41. Means of transport 41. Transpordivahendid 42. Measuring accuracy 42. Mõõtetäpsus 43. Measuring device 43. Mõõteseade 44. Measuring tape 44. Mõõdulint 45. Meet the requirements 45. Nõuetele vastama 46. Melting kettle 46. Sulatuskatel 47. Merging lane 47. Liitumisrada, pealesõidurada 48. Mesh reinforcement 48. Võrkarmatuur 49. Metering 49. Mõõtmine 50. Mickle hammer 50
again the following night. Before the wolves leave, they request to familiarize themselves with the particular scents of the Cullens, so that during battle there are no mistakes. Each wolf, in turn, approaches the individual members of the Cullen family, smelling and sniffing them all. Bella recognizes Jacob as the reddish-brown wolf. She realizes he seems the most relaxed of the pack. Jacob meets her gaze and comes closer. Bella notices that Edward is measuring her reactions, clearly hoping to find her afraid or disgusted by what she sees. But instead of being afraid, Bella reaches out and runs her fingers through Jacob's fur. She is surprised by how it is both rough and soft. Suddenly Jacob licks her across her entire face, laughing and jumping out of the way when she yells and smacks at him playfully in response. Both vampires and werewolves, and especially Edward, are all shocked and bewildered by the encounter.
Dictionar y (,,All Marketers Are Liars") A Abandon hülgama, loobuma Accidental juhuslik Adequate adekvaatne, piisav Advertisement reklaam, kuulutus Affect mõju Airwaves õhuvoolud Alas paraku All stripes vöödilised Antibiotic antibiootiline, antibiootikum Apparently ilmselt Appeal palve Artisan kunstkäsitööline Asset vara, väärtus Assumption eeldus Auction oksjon Audacious hulljulge, ebatavaline Authentic ehtne Authenticity ehtsus Average keskmine B Barber juuksur Bearing kurss Bending nõtk, painutamine Benefit kasu, tulu Benevolent lahke Beverage jook Blacksmiths sepad Bloodletting...
The United States and its economy are known to be one of the thriving and strongest in the world. It represents 16.6% of the world’s total GDP. The estimated worth of USA's GDP is estimated to be around 17.5 trillion dollars and dollar being the third currency in the world and the official currency of the US. They also manage a 5% growth every quarter. So how do they manage it? There are three main sectors that contribute to the USA's GDP. First is services that is 80% of the total GDP. The output of services in 2014 was 13,8 billion dollars witch was the nr.1 in front of European Union’s output witch was 13,4. The second contributing sector is the industry sector which provides 19% of the country’s GDP. In this area USA has fallen behind and has to accept the third position in the world’s total industry's output. First in industry’s output last year was European Union who had 4,6 billion dollar output, not far was China who ha...
– Screens – Sealing the machines Glare – Outside surface of machines should be lowered to <45˚C Colour temperature Hard physical occupations in extreme conditions Colour Rendering Index (CRI) should be automized Distant piloting Ventilation Protective clothing Light technical measuring IONIZING AND NON- system IONIZING RADIATION Consists of 4 main variables: Ionizing radiation consists of highly-energetic particles or waves that can detach (ionize) at least one electron from an atom or molecule (beta- Measures Symbol Unit
the two countries, 15 km (9.3 mi) north of the Friendship Bridge. Panama Canal Date started:January 1, 1880 Date finished:January 7, 1914 Location:Isthmus of Panama The Panama Canal is a 77 km ship canal in Panama that joins the Atlantic Ocean and the Pacific Ocean and is a key conduit for international maritime trade. Built from 1904 to 1914, annual traffic has risen from about 1,000 ships in the canal's early days to 14,702 vessels in 2008, measuring a total 309.6 million Panama Canal/Universal Measurement System (PC/UMS) tons. In total over 815,000 vessels have passed through the canal.One of the largest and most difficult engineering projects ever undertaken, the canal had an enormous impact on shipping between the two oceans, replacing the long and treacherous route via either the Strait of Magellan or Cape Horn at the southernmost tip of South America. A ship sailing from New York to San Francisco via the canal travels
Miina Härma Gymnasium Acid Rain Report Compiler: Teisi Timma 8a Teacher: Esther Linask Tartu 2009 Acid Rain Acid rain is rain consisting of water droplets that are unusually acidic because of atmospheric pollution - most notably the excessive amounts of sulfur and nitrogen released by cars and industrial processes. Acid rain is also called acid deposition because this term includes other forms of acidic precipitation such as snow. Acidic deposition occurs in two ways: wet and dry. Wet deposition is any form of precipitation that removes acids from the atmosphere and deposits them on the Earth's surface. Dry deposition polluting particles and gases stick to the ground via dust and smoke in the absence of precipitation. This form of deposition is dangerous however because precipitation can eventually wash pollutants into strea...
While writing this thesis the author studied the working principle of optical sensors, analysed different solutions, disregarding all that did not suit the needs of this work and concentrated on thouse that showed the most potential. Also the calibration method of water meters was carefully examined, which stated the requirements that the optical sensors should fullfill while working. The practical part of the work was made simpler by authors two years of experience with water meters and measuring equipment used for the process. The results in table 8.1 show that the measuring deviation during the process stays well within the deviation calculated by the calibration of Metrosert AS water meter measuring equipment. Using one optical sensor with the process decreases the time consumption by 6.25 %. Equipping the measuring device with 6 optical sensors decreases the time consumption of measurements by 61.73 %.
Üldiselt tekivad e-süsteemides probleemid kas selle enda võimekusest või ettevõtte sees olevatest muutujatest. Kuna süsteem ei hinda erinevaid taotlusi ja hinnapakkumisi samamoodi kui inimene, siis ei pruugi ostja selle tagajärjel parimat võimalikku hinda saada. Samas kogu süsteemi edukal ellurakendamisel on võimalik saavutada märkimisväärne kuluefektiivsus, kui toimib kõigi tarneahelas osalevate lülide sümbioos. Kasutatud allikad : • Veebiartikkel – Measuring e-procurement benefits by David Eakin • Veebiartikkel – The Architecture of Web-Based Procurement by Dale Neef • Purchasing and Supply Chain Management – Lysons, Farrington
Forestry Importance: · Environmental-protective importance Oxygen Cleans the air/soils/ground water Protects the soil from erosion · Timber Firewood Woodwork Building materials Timber cellulose paper · Mushrooms/berries/juices · Habitat of different species Measuring the amount of forest: · Fixing the area under the forests (ha/%) -> In Estonia 47.4%, 2.143 mil/ha It doesn't take into account the amount of timber · To measure the amount of timber (m3) -> 352.7 mil/m3 It doesn't take into account the annual increase · To fix different species of trees (%) -> Pine 40%, Birch 30%, Spruce 20% · To measure the annual increase of timber (m3, ha, year) -> 9 mil. m3/ha/year Main principle of the economy of forests: Annual cutting should be equal to annual increase. Trees are divided into: · Precious trees (ebony, mahagony, sandalwood) · Hard-br...
Switzerland. 7. 70% of the world's wool comes from Australia. We have over 126,000,000 sheep, which use fully half the continent for grazing. 8. The longest fence in the world is in Australia, and it runs for over 5,530 kms. It's designed to keep dingoes away from the sheep. 9. The wine cask, the ubiquitous plastic bag full of wine contained in a cardboard box, was invented in Australia in 1967. 10. The world's longest golf course, measuring more than 850 miles long is located in Australia. Canada 1. Canada is one of the only countries that confederating without war. 2. Canada, the 2nd largest country in the entire world has less than 35 million people. 3. Canada has 10 provinces and 3 territories. Nunavut is the 4th largest subdivision of a country in the world. 4. Toronto, Canada is home to the largest tower in the world, the C.N. Tower. 5
Codecs 42 Interrupt Rate 43 Dual-Function Pins on Microcontrollers 43 Design Checklist 45 v 3 Sensors 47 Temperature Sensors 47 Optical Sensors 59 CCDs 72 Magnetic Sensors 82 Motion/Acceleration Sensors 86 Strain Gauge 90 4 Time-Based Measurements 93 Measuring Period versus Frequency 95 Mixing 97 Voltage-to-Frequency Converters 99 Clock Resolution 102 5 Output Control Methods 103 Open-Loop Control 103 Negative Feedback and Control 103 Microprocessor-Based Systems 104 On-Off Control 105 Proportional Control 108 PID Control 110 Motor Control 123 Measuring and Analyzing Control Loops 130
B5M0248B B5M0247B B5M0249B 3. Datum Dimensions NOTE: ¼ A suffix character "R" or "L" refers to the right or Use a tram tracking gauge to measure all dimen- the left. sions. If a measuring tape is used, be extremely ¼ All dimensions refer to the distance between the careful because it tends to deflect or twist, which centers of holes measured in a straight line. results in a false reading. ¼ Each dimension indicates a projected dimension between hole centers. G5M0122
The difference is that GDP defines its scope according to location, while GNP defines its scope according to ownership. In a global context, world GDP and world GNP are therefore equivalent terms. · GDP is product produced within a country's borders; · GNP is product produced by enterprises owned by a country's citizens. International Standards The international standard for measuring GDP is contained in the book System of National Accounts (1993), which was prepared by representatives of the International Monetary Fund, European Union, Organization for Economic Co-operation and Development, United Nations and World Bank. Nominal GDP and Real GDP The GDP calculation is distorted by inflation. This unadjusted GDP is known as the nominal GDP. In practice, GDP is adjusted by dividing the nominal GDP by a price deflator to arrive at the real GDP.
clouds that are seen when looking at Saturn are just the top layer of a very deep layer that covers a center of liquid hydrogen. The clouds are blown by constant winds that reach speeds up to one thousand miles per hour at the equator of the planet ("Great Space Place"). The rings of Saturn are more spectacular than those of any other planet. Although this planet's rings are very wide, extending from the top of its atmosphere to well beyond the orbits of its closest moons, they are very thin, measuring no more than a few kilometers (about a mile) in thickness ("Great Space Place"). The Pioneer 11 flyby made several discoveries about the rings. The rings are made of particles that are dust-sized up to large mountain-sized masses, with the average size being in the marble to basketball range - about 10 centimeters (four inches). These particles are extremely cold and are possibly composed of frozen water and other ices. An extensive cloud of hydrogen was also discovered around the rings
neil lihtsalt loota, et see peagi ka paranema hakkab. 17 VIIDATUD ALLIKAD 1. Grönroos, C. 2000. Service Management and Marketing: A Customer Relationship Management Approach. 2. Perens, A 1998. Teenuse margeting. Tallinn 1. Maxima poekett [http://www.maxima.ee/ettevottest/kes-me-oleme/missioon-ja- visioon/] 18.03.2011 2. Parasuraman A , Zeithaml V., Berry L 1988.Servqual: a Multiple Item Scale for Measuring Customer Perceptions of Service Quality. 3. Parasuraman A, Zeithaml V, Berry L, 1994.Alternative Scales for Measuring Service Quality. 4. TNS Emor, Ostumüsteeriumist ehk mystery shoppingust [http://www.emor.ee/ostumusteeriumist-ehk-mystery-shoppingust/] 18.03.2011 18 Lisa 1. Külastusprotokoll 1-ei 2-ei 3- pigem ei 4- ei oska 5- pigem 6- 7- nõustun
of integrated care. For instance, the association between the features of integrated systems and high-performance systems may not imply causation. Evaluators therefore need to ensure clarity about whether they are comparing integrated against fragmented care; more against less integrated care; or a newly integrated model against a previous less integrated model. 18 What is integrated care? Measuring the extent of integrated care A key challenge for policy-makers and planners pursuing evaluation is to develop more suitable approaches to measuring and assessing integrated care. Such work requires sound theoretical underpinnings in order to guide evaluation and measurement, and the use of both quantitative and qualitative methods. Such an approach might help measure integration, for instance, not only in relation to the impact on health
This can tell us a lot about the GCR sources and the cosmic rays' trip through the Galaxy. The "composition" of cosmic rays describes what fraction of cosmic rays are protons, what fraction are helium nuclei, etc. All of the natural elementsin the periodic table are present in cosmic rays, in roughly the same proportion as they occur in the solar system. But detailed differences provide a "fingerprint" of the cosmic ray's source. Measuring the quantity of each different element is relatively easy, since the different charges of each nucleus give very different signatures. Harder to measure, but a better fingerprint, is the isotopic composition (nuclei of the same element but with different numbers of neutrons). To tell the isotopes apart involves, in effect, weighing each atomic nucleus that enters the cosmic ray detector. About 90% of the cosmic ray nuclei are hydrogen (protons), about 9% are helium (alpha particles),
Steep- a steep slope rises quickly and is difficult to climb Terraced house- a house in a row of similar houses joined together on both sides. The American word is row house Utility room- a small room in some houses that contains equipment such as a washing machine Virtually- used for emphasizing that a statement is almost completely true Winding- a winding road, river etc has a lot of bends in it Yard- a unit for measuring length. There are three feet or 36 inches in a yard. One yard is equal to 0.91 metres. Unit3 words Maintenance job- work that is done to keep something such as a building, machine, or piece of equipment repaired and in good condition Milk float- a small truck used for delivering milk to people's homes Obsessed- considering someone or something as so important that you are always thinking about them, in a way that seems extreme to other people
estate. In and around the Hall, grew up the major institutions of the British state: Parliament, the law courts and various government offices. The hall was built from 1097-99 on the orders of William Rufus, son of William the Conqueror. Westminster Hall has the largest clearspan medieval roof in England, measuring 20.7 by 73.2 metres.
orbitaalpositsiooni ning kellaaega, millal see andmepakett teele saadeti. Vastuvõtja arvutab tarkvara abil välja mitmelt satelliidilt tuleva asukoha- ja ajainfo omavahelise suhte abil aga välja oma asukoha. Ilma raadiolaineteta oleks seda üsna raske teha. [15] Kuid GPS ja selle alternatiivid pole ainsad raadionavigatsiooniviisid. Lennukitele on üsna olulised VOR ja VOR/DME jaamad (pilt 3) (Very high frequency Omnidirectional radio Range/Distance Measuring Equipment), mille näol on tegemist raadiosaatjajaamaga, mis kiirgab välja esmalt n.n. master-signaali ning 30 korda sekundis täispöörde tegev (vanasti mehhaaniliselt, tänapäeval on kasutusel suurem hulk antenne mida kordamööda sisse lülitatakse ringikujuliselt) antenn kiirgab välja äärmiselt suunatud sekundaarse signaali, mis ajastatakse täpselt nii, et selle faasinihe seoses master-signaaliga oleks võrdne liikuva antenni positsiooniga magneetilise põhja suhtes
· Processing time is the time required by the other company to manufacture the product. · Post processing time is the time required to do the quarantine and inspection process, after manufacturing. After the lead time, the product will be available in the inventory after receiving the item from the manufacture or retailer. Lead time can be reduced by measuring and eliminating the errors made during the lead time process. Lead time can also be reduced by using Electronic Data Interchange (EDI) strategy. "JustinTime" (JIT) is a popular strategy used by manufacturing and production companies to improve efficiency in their business. Thus, for stable supply chain and development in the business growth, it is important to understand the causes and effects of bullwhip effect. Implement the business strategies
1939. 129 ülesannet: 2-22 aastani 1960. 142 ülesannet: 2-22 aastani 1972. restandardiseerimine 1985. neljas versioon 1. Suur standardiseerimise grupp 2. IQ kasutamine 3. Hoolikalt koostatud skoorimisjuhend. Alates 1921 aastast nn. geeniuste uuring - 5 köidet "Genetic Studies of Genius" B. Robert M. Yerkes (1876-1956) 6. aprillil 1917 Woodrow Wilson kuulutas USA astunuks I Maailmasõtta. Yerkes, R.M. (1917) The Binet versus the point scale method of measuring intelligence. J. Applied Psychology, 1,111-122. Army Testing Project 1. Test peab olema grupitest. 2. Mõõtma võimekust, mis sõltuks võimalikult vähe haridusest. 3. Test peab olema kasvava raskusega: lihtne madala võimekusega, raske kõrge võimekusega inimestele. 4. Testimise aeg peab olema kuni 1 tund. Army Alpha Test:8 alltesti (verbaalsed ülesanded) Army Beta Test:7 alltesti (m.verbaalsed ülesanded) 1919 aasta alguseks oli testitud 1 726 966 meest. M.A.=13.08 a.; 47
1939. 129 ülesannet: 2-22 aastani 1960. 142 ülesannet: 2-22 aastani 1972. restandardiseerimine 1985. neljas versioon 1. Suur standardiseerimise grupp 2. IQ kasutamine 3. Hoolikalt koostatud skoorimisjuhend. Alates 1921 aastast nn. geeniuste uuring - 5 köidet "Genetic Studies of Genius" B. Robert M. Yerkes (1876-1956) 6. aprillil 1917 Woodrow Wilson kuulutas USA astunuks I Maailmasõtta. Yerkes, R.M. (1917) The Binet versus the point scale method of measuring intelligence. J. Applied Psychology, 1,111-122. Army Testing Project 1. Test peab olema grupitest. 2. Mõõtma võimekust, mis sõltuks võimalikult vähe haridusest. 3. Test peab olema kasvava raskusega: lihtne madala võimekusega, raske kõrge võimekusega inimestele. 4. Testimise aeg peab olema kuni 1 tund. Army Alpha Test:8 alltesti (verbaalsed ülesanded) Army Beta Test:7 alltesti (m.verbaalsed ülesanded) 1919 aasta alguseks oli testitud 1 726 966 meest. M.A.=13.08 a.; 47
situations. Although, the regulation of emotions has always been a crucial part of human existence, however, research into emotion regulation (ER) is relatively recent. Emotion regulation in relation.. 7 Nonetheless the research interest in processes involved in ER has grown rapidly. Increasingly attention has been directed to unintentional regulation of emotions and the ways of measuring the biological responses in ER (Wirtz et al., 2006, Rimmele et al, 2007). Previous research interest in ER was largely focused on intentional- responsive regulation, (Muraven et al 1998; Gross & Levenson 1997; Wegner, Erber & Zanakos 1993) where only intentional responses where recorded, and the data was based mainly on self-reports. Consequently LeDoux (2000) pointed out the need to discover new approaches in emotional research. Furthermore, while some field
essarily overload this bulkhead, so we is heavy, really heavy, and/or the wings of present day aircraft rarely better seek the designer's advice. floor is not very rigid, and/or the fix- use more than a few degrees of twist. One way to avoid complications in ture is not very stiff, we may At the high AOA occurring during this situation is to support the wing experience difficulties in measuring that intense pull up, this small spar(s) outside the fuselage at the wing deflection during the proof amount of twist has almost no influ- point where the wing "enters" the loading. We can, of course, perform ence on the lift distribution and can fuselage (Figure 6). We realize this is the proof loading of the wing with- be neglected here. By the way, by
Tagab patsiendile turvatunde. Lõpetamine · Tee käte antiseptika, vajadusel kätehügieen. · Dokumenteeri o mõõtmise kellaaeg, o pulsisagedus, o teised hinnatavad pulssi iseloomustavad näitajad. Kasutatud kirjandus Iivanainen, A., Jauhiainen, M., Pikkarainen, P. (2003). Õendusoskused. Tallinn: Medicina. Philip, J. (1991). A high-voltage pulse measuring system based on the Kerr effect. Measurements Science and Technoogyl, 2, 565567. Potter, P. A., Perry, A. G. (1997). Fundamentals of Nursing. Mosby Year Book. St. Missouri. Potter, P. A., Perry, A. G. (2002). ClinicalNursing Skills & Techniques, Mosby - Year Book. St. Missouri. Taylor, C., Lillis, C., LeMone, P. (1989). Fundamentals of Nursing. Philadelphia: J. B. Lippincott Company. deWit, S. C. (2005). Fundamental Concepts and Skills for Nursing. Philadelphia: Elsevier Saunders
TARTU ÜLIKOOLI PÄRNU KOLLEDŽ Turismiosakond Kvaliteedijuhtimine Teenuste disain ja juhtimine Magistriõppekava Kursusel omandatud teadmiste hindamise test ● Testi leiate ÕIS-ist ning selle eesmärgiks on kvaliteedijuhtimise alaste teadmiste kinnistamine. ● Saatke vastustega test hiljemalt 01.12.2015. a. aadressil: [email protected] ● Testi hindamisel kasutatakse põhimõtteliselt samu põhimõtteid, mis on esitatud Töö (nelja eksamhinde saamiseks vajaliku töö) hindamiseks iseseisvate tööde juhendi lõpul. Testi sooritamise eest on võimalik saada kuni 30 punkti. Nimi: Esitamise kuupäev: Test koosneb kahest osast: I osa – Kvaliteedi teoreetilised käsitlused II osa – Kvaliteedi mõõtmise ja...
individual experience · Usually measured by questionnaire; descriptive · `Why and how' of development are important · `Why and how' are not so important · Standard measures difficult or impossible to obtain Measuring Personality Personality · Self-report tests Questionnaires (yes/no, true-false, agree-disagree) Nomothetic Idiographic Adjectives E.g. Minnesota Multiphasic Personality Inventory (Schacter p. 492) Trait Psycho- Humanistic Social · Rating scales
Future research will focus on improving the indicators used to map interactions in national innovation systems as well as the linkages to the innovative performance of firms and countries. These indicators are at an early stage of development and do not approach the robustness of more conventional measures such as R&D expenditures. A main goal is to improve the comparability of studies across countries by encouraging those engaging in analysis of innovation systems to focus first on measuring a core set of knowledge flows using similar indicators. At the same time, specific analyses will be directed to deepening the understanding of certain types of flows in national innovation,namely: human resource flows;2) institutional linkages; 3) industrial clusters; and 4) innovative firm behaviour. Benchmarking NIS Learning from foreign systems of Innovation (Tidd et al, 2005) ● Reasons for monitoring and learning from the development of
They have to be willing to change and motivate workers to do the same. They have to take into account that pay-for performance will bring extra responsibilities- paperwork, resolution of conflicts and so on. They have to be able to actually make a distinguish between those who perform better than others, and they have to be able to behave accordingly. It means that civil service needs very competent managers. The problem in pay-for performance is largely in lack of measuring and documenting performance so it would be accurate and complete. Since there are no agreement on standards, indicators, measurement of performance to assess civil servants, the process is very messy and understandable. Consternating on private sector has made it even more vague and difficult to follow- it just does not work the same in public sector. Another problem with pay-for performance lies in fairness of the process. For a employee
Isiksusepsühholoogia. Tartu: Tartu Ülikooli Kirjastus 2. Diamantopoulou, S., Rydell, A.M,. & Henricsson, L,. 2008. Can Both Low and High Self-Esteem be Related to Agression in Children?, Blackwell Publishing, 1,4, 12-15 3. Fennell, M., 1999/2005; Võit madala enesehinnangu üle. Tallinn: Tänapäev 4. Kammeyer-Mueller, J.D., & Judge T.A. 2007. Self-Esteem and Extrinsic Career Success: Test of a Dynamic Model. Applied Psychology, 1, 8, 10. 5. Kernis, M.H. 2005. Measuring Self-Esteem in Context: The Importance of Stability of Self-Esteem 6. Kon, I., 1978/1981; ,,Mina" avastamine. Tallinn: Eesti raamat 7. Nestler, J., 2007. Self-esteem and curing stress and burnout. [Online] http://www.earticlesonline.com/Article/Self-esteem-And-Curing-Stress-And- Burnout/177682 [23.10.2009] 8. Randmann, L., Suhtlemispsühholoogia. [Online] http://www.enop.ee/tpi/randmann/materjal/HHP3800%20-%204.%20Isiksus.pdf [20.11.2009] 9. Reasoner, R
1) External Environment - Analysis of the external environment focuses on issues such as product, labour, and capital markets and regulatory structures. These issues, in turn, relate in part to the risks and opportunities associated with management of the economic, environmental, and social aspects of the business. Overlaps and synergies exist between the conventional indicators used for analysis of the external environment and those used for measuring economic, environmental, and social performance. For example, social indicators related to the composition and status of the workforce may be used to highlight opportunities for expanding the firm’s intellectual capital. 2) Competitive advantage– is built through cost leadership and product/service differentiation and, increasingly, through the formation and retention of intellectual capital
development. Harvard Law School International Tax Programme, 1966. 10. IMF Government Finance Statistics yearbook, 2001, Washington. 11. 2002. aasta riigieelarve täitmise aruanne. Tallinn, 2003. 12. 2003 aasta riigieelarve täitmise aruanne. Tallinn, 2004. 13. Kallas, S. Kõne Riigikogus 10. novembril 1999. - Riigikogu protokollid, 1999, lk. 815817. 14. Konjunktuur, 2003, nr. 1. 15. Lotz, I. R., Morss E. R. Measuring tax effort in developing countries. - IMF Staff Papers, 1967, No. 14, pp. 478499. 16. Majandusülevaade. Rahandusministeerium. http://www.fin.ee/ 17. Musgrave, R. A. Fiscal systems. New Haven CT: Yale University, 1969. 17. Musgrave, R. A. Tax reform in developing countries. - The theory of taxation for developing countries. New York: Oxford University Press and World Bank, 1987. 18. Raju, O. Estonian`s experiment in abolition corporate income tax
Suspensioonid, emulsioonid 3. Millist infot dispersse süsteemi kohta annavad osakeste mõõtmete diferentsiaalne ja integraalne jaotuskõver? 4. Millest on tingitud valguse hajumine disperssetes süsteemides ja tõelistes lahustes? Milliste parameetritega iseloomustatakse kvantitatiivselt valguse hajumist? 5. Mille poolest erinevad nefelomeetria ja turbidimeetria meetodid? A nephelometer [1] is a stationary or portable instrument for measuring concentration of suspended particulates in a liquid or gas colloid. A nephelometer measures suspended particulates by employing a light beam (source beam) and a light detector set to one side (often 90°) of the source beam. Particle density is then a function of the light reflected into the detector from the particles. To some extent, how much light reflects for a given density of
For each research question one or more survey questions are then formulated, depending on the goal of the study. For example, in a general study of the population one or two general questions about well-being are enough to give a global indication of well-being. On the other hand, in a specific study of the influence of social networks on feelings of well-being among the elderly a far more detailed picture of wellbeing is needed and a series of questions has to be asked, each question measuring a specific aspect of well-being. These different approaches are illustrated in the text boxes noted later. Survey methodologists have given much attention to the problems of formulating the actual questions that go into the survey questionnaire (cf. Fowler & Cosenza, Chapter 8). Problems of question wording, questionnaire flow, question context, and choice of response categories have been the focus of much attention. Much less attention has been directed at clarifying the problems
annaabi.ee 
Sisene Facebook'ga
Sisene Google'ga
Sisene LinkedIn'ga
